741 replies to this topic

[Oaken]

i wanna join a room!, im pretty good

999998

help xD

[Voltron]

If we pass the rods but fail the next part do you have to start again?

No you just restart that test.

[adonis]

once you get past heat it stays on acid unless everyone leaves

I can get you to acid if you need a hand but after that im out no excel for gravity

[dotnetex]

Testing Station
Step One - Heat Test

This activity is very seems very simple but it really isn't. All you have to do is to move your lever until you see that your piston is right next to the first little spec of light (the littlest one). You move the piston to the right by dragging your lever over to the right (and then dragging it to the left if you go too far).

Alternatively, for a more accurate piston level, check out the puz4_data.phtml page. You'll see a whole string of data with a message. Towards the end, you'll see two sets of four numbers seperated by pipes and commas (|). Look at the second set, and the first number out of the four is what your piston needs to be set at.

Example: [other data] ... |0,x,y,z|78,2,53,51|
(sample data)

Now, see the number in bold, that will be where your number is located on your own puz4_data.phtml page. Once you figure it out (within the 30 second time limit of course), quickly move your piston to get it as close as humanly possible. You have about a one over or one under margin of error, or else you'll be wrong.

Edited by dotnetex, 06 March 2008 - 02:31 PM.

[sarah.]

This thing is ridiculous. x__x

Sorry guys, I can't do that crap. xD

[Oaken]

This thing is ridiculous. x__x

Sorry guys, I can't do that crap. xD

It really is

I keep getting it wrong.

[Voltron]

Wow I got the rod wrong somehow x.x

Try this Sarah and Oaken. Do you see the shadow that the light thing makes? Try putting it right at the edge of that.

[dotnetex]

If you follow the instructions i got from another fansite, it should be very easy!

whenever we have to set the rod again, click on the link and it will give you the new coordinates

Edited by dotnetex, 06 March 2008 - 02:33 PM.

[Voltron]

If you follow the instructions i got from another fansite, it should be very easy!

It is easy. For me

[sarah.]

Wow I got the rod wrong somehow x.x

Try this Sarah and Oaken. Do you see the shadow that the light thing makes? Try putting it right at the edge of that.

I can't be bothered with it to be honest. I'm just gonna go make dinner instead (even though it's 10.30pm).

[Voltron]

I can't be bothered with it to be honest. I'm just gonna go make dinner instead (even though it's 10.30pm).

Awww, Come on

[adonis]

heat part is simple

[Oaken]

I got it now

Havn't had one wrong for a while anyway.

[dotnetex]

Testing Station
Step One - Heat Test

This activity is very seems very simple but it really isn't. All you have to do is to move your lever until you see that your piston is right next to the first little spec of light (the littlest one). You move the piston to the right by dragging your lever over to the right (and then dragging it to the left if you go too far).

Alternatively, for a more accurate piston level, check out the puz4_data.phtml page. You'll see a whole string of data with a message. Towards the end, you'll see two sets of four numbers seperated by pipes and commas (|). Look at the second set, and the first number out of the four is what your piston needs to be set at.

Example: [other data] ... |0,x,y,z|78,2,53,51|
(sample data)

Now, see the number in bold, that will be where your number is located on your own puz4_data.phtml page. Once you figure it out (within the 30 second time limit of course), quickly move your piston to get it as close as humanly possible. You have about a one over or one under margin of error, or else you'll be wrong.

IF YOU FOLLOW THESE INSTRUCTION TO THE TEE, YOU WILL NEVER!!!! BE WRONG

[Voltron]

Actually you were wrong once.

[Oaken]

IF YOU FOLLOW THESE INSTRUCTION TO THE TEE, YOU WILL NEVER!!!! BE WRONG

Is everyone remembering to lock their bar in place? I have not had one wrong since I found out you could lock it

Actually you were wrong once.

That's because I was disconnected from the internet. I had to turn my router off

[adonis]

lol who jumped away? I only missed 1......... stupid contacts

[Oaken]

lol who jumped away? I only missed 1......... stupid contacts

I can't stay on for much longer

Someone come and be the fourth person please!!

[Aerowyn]

I'm there and waiting for a fourth person in #999998. :\

[Highly-Advanced-Cube]

Sorry i would join but my account got suspended by TNT >.<

Btw: http://www.jellyneo....=sloth&id=day07

has a calcuator for each part.

[Aerowyn]

;__: come on guys, just ONE MORE person for #999998. PLEASEEE. We've been sitting here for a long while now. We just need a fourth.

[mumsiey]

I wonder if we can just do some of this step & still get to move on, I was thinking this steps is kinda like the grave digging in the other plot, do as many as you want to so you would get more points at the end, or be lazy & just do a few.... any thoughts?

[Highly-Advanced-Cube]

As i said before this step can be skipped as it is not a necesarry step for the plot.

[adonis]

As i said before this step can be skipped as it is not a necesarry step for the plot.

bonus plot points!!!!

[Sunset]

I really hate this plot, though I said that about every plot whenever I was confused about something ... heh oh well!